Expert Answers about Chrysler Town and Country

• 4-Way Trailer Wiring Harness to Fit a 2015 Chrysler Town and Country
• To tow a trailer with your 2015 Chrysler Town and Country I recommend the Curt T-Connector Vehicle Wiring Harness # C56331. It's a 4-way wiring connector to power the trailer's lights and it plugs in behind the van's tail lights. You also need to run a hot wire from the harness to the van's battery and insert the included fuse. I've linked the install details and a video from when we installed it. If you also need a trailer hitch reciver I recommend the Draw-Tite, part # 75579, that's...
  view full answer...


• Adapting Yakima Raptor Bike Rack to a 2013 Chrysler Town & Country with Factory Roof Rack
• All you will need to adapt your Yakima Raptor bike rack to the crossbars on your 2013 Chrysler Town and Country are the universal MightyMounts, # Y03590. I have linked a video review of these for you.
  view full answer...


• 7-Way RV Trailer Connector Mount for Curt Trailer Hitch # 13364 on a 2010 Chrysler Town and Country
• To convert your 4-Way trailer connector you will need the Brake Controller 7 & 4 Way Installation Kit, item # ETBC7, which includes everything needed to upgrade your trailer connector to a 7-Way RV connection. We have detailed installation instructions for you to review, see link. The one other thing you will need is a No-Drill Mount Bracket, # C57202 (long) , to attach the connector to the hitch. You will bolt the bracket included in the # ETBC7 wiring kit to this bracket and then attach...
  view full answer...


• Parts Needed to Add 7 Way Trailer Connector to 2010 Chrysler Town and Country
• Since you already have a 4 way flat on your 2010 Chrysler Town and Country, to add a 7 way connector you'll need to use the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7. This gives you all of the parts you'll need to install a 7 way on your 2010 Chrysler Town and Country and allow you to tow a trailer with brakes. If you don't already have a brake controller, I recommend using the Tekonsha Prodigy P3 Trailer Brake Controller...
  view full answer...


• Equipment Needed to Tow Riverside Retro 165 Travel Trailer With 2016 Chrysler Town & Country
• Don't worry, we can help you with this! Anytime the trailer's fully loaded weight is greater than half the weight of the vehicle towing it, we recommend using weight distribution. Since a 2016 Chrysler T&C weighs about 4700 lbs, I would advise using a weight distribution hitch. A weight distributing hitch will increase the capacity of the hitch, but NOT that of the vehicle. In your case, you'll still be limited to the 3600 lb towing capacity of the vehicle, regardless of whether or not...
  view full answer...


• Parts Needed to Change Thule One Key Lock Cores
• In order to change Thule One-Key System lock cores you'll need the Universal Change Key for Thule One Key Locks # 853-1251.
  view full answer...


• Replacement Headlight Bulbs for 2014 Chrysler Town & Country
• To replace the headlight bulbs on your 2014 Chrysler Town and Country you will choose a set of new type H11 bulbs. You only need two bulbs, not four. The linked page shows all bulbs of this type that are DOT-compliant (legal) for on-road use and these include the standard Halogen type like # VX-LH11, which is the item you referenced in your question. These are just like your factory bulbs. If you would like bulbs that are still DOT-compliant but that are brighter than the factory bulbs...
  view full answer...


• Parts Needed to Add 7-Way and Brake Controller on 2014 Chrysler Town and Country
• Thanks for that photo, which shows you do have a 4-way like Wiring Harness # C56331 on your 2014 Chrysler Town and Country and we have exactly what you need in order to add a brake controller. You will simply need to add the Universal Installation Kit for Trailer Brake Controller # ETBC7, which will give you a 7-way connector, circuit breakers and the rest of the hardware needed to install a brake controller. The 7-way will power your trailer's electric brakes as well as its lights. For...
  view full answer...


• Parts Needed For Carrying a Scooter With a 2015 Chrysler Town and Country
• If you are loading the scooter in the back of your 2015 Chrysler Town and Country I feel like you will only need a Ramp # EM07441 to load your Scooter. This will not require any installation, only unfold the ramp when you need to load and unload the scooter. If you are going to have a Trailer Hitch Receiver # e98854 you can find a local installer by using the "Locate installers near me" link located under the pictures and install videos on the product page. This will give you a list of...
  view full answer...


• How to Flat Tow a 2000 Chrysler Town and Country Behind a Motor Home
• According to my research your 2000 Chrysler Town and Country can be flat towed with all 4 wheels on the ground as long as you use a transmission lube pump from Remco Industries. We sell everything else you would need except for the lube pump. First you will need base plates # 242-2. Then, for a compatible tow bar, you can use the Falcon 2 # RM-520. I have linked a video of this tow bar for you. You will also need safety cables # RM-643. The coiled design helps keep them off of the ground. For...
  view full answer...


• Trailer Hitch Receiver for 2016 Chrysler Town and Country
• For the installation of the Curt Trailer Hitch Receiver # 13364 on your 2016 Chrysler Town and Country you will be reusing the bolt already in place that hold on the bumper. So you will not need to acquire any bolts unless they are missing or become damaged during removal. If you are going to be hauling a trailer or adding on a carrier that might interfere with the visibility of your tail lights then I recommend installing a 4-way plug. The Curt Vehicle Wiring Harness # C56331 will give...
  view full answer...


• Parts Needed to Install Tekonsha Prodigy P2 or P3 on 2008 Chrysler Town & Country
• You can't go wrong with either of the brake controllers you mentioned. The main difference between the controllers is how user-friendly the display is. The Prodigy # 90885 P2 uses an digital display that will display error codes in the event of any problems with the trailer's braking system. The Prodigy # 90195 P3 has a more user friendly display, which will actually spell out any problems, rather than an error code that you'll need to go look up. To install the brake controller, you'll...
  view full answer...


• What Fuse Rating is Needed to Protect the 12 Volt Accessory Power Cirucit on a 7-Way Connector?
• To protect the 12 volt accessory power supply circuit, we recommend using a 40 amp inline circuit breaker, part number 9510.
  view full answer...


• Brake Controller Wiring for 2016 Chrylser Town and Country
• To install the Prodigy P2 # 90885 brake controller in your 2016 Chrysler Town and Country with 4-way harness # C57186 there is only one other thing you'd need, the Universal Installation Kit for Trailer Brake Controller # ETBC7. This kit will give you the rest of the necessary parts required to install the P2 - wiring, circuit breakers, hardware, as well as a 4-way to 7-way adapter. The only other thing I recommend is part # 10-2-1, which is 10 gauge wire by the foot for longer vehicles...
  view full answer...


• Parts Needed to Install Electric Brakes On 1995 Coleman Destiny Royale Trailer
• To make sure that you get the correct parts, I would need to know the inner and outer bearing numbers stamped into the metal of the bearings. There are different 5 lug bolt patterns. Use the FAQ I have linked to measure for bolt pattern so you can get the correct hub and drum assemblies. If you do not have EZ Lube axles, you will not need EZ lube hub and drum assemblies. If you do have L44649 inner and outer bearings and the seal has a 1.987 outer diameter and 1.5 inch inner diameter,...
  view full answer...


• Replacement Trailer Tires for Size 20.5 x 8 - 10
• Those are some extremely old tires. We recommend changing them every 6 years or so regardless of tread wear. The metric size for your 20.5 x 8 - 10 tires is 205/65-10. Our most popular tire in this size is # AM1HP54. It has a load range D and max capacity of 1,330 pounds at 70 psi. If you'd like a higher rated tire we have # AM1HP56 with an E load range rated for 1,650 pounds at 90 psi. Both tires have a 2-year limited warranty.
  view full answer...


• Parts Needed For Installing a Trailer Brake Controller On 2013 Chrysler Town and Country With 4-Way
• As it sounds like you have a Curt Trailer Connector Adapter # C57672 on your 2013 Chrysler Town and Country you will need the Wiring Kit # 5506. This will contain the wiring, connectors and circuit breakers needed to power a brake controller as well as the charge line for the trailer breakaway battery. I recommend using the Redarc Tow-Pro Liberty Brake Controller # RED52VR. This brake controller uses a small dash mounted control knob to give it a clean look. The main unit will be hidden...
  view full answer...


• Adding 7-Way Trailer Connector for Brake Controller on 2008 Chrysler Town and Country
• Just about everything you need is available in one kit. Take a look at the 4 and 7-Way installation kit # ETBC7. This kit provides a 7-Way (the existing 4-Way will just plug into the 4-Way receptacle on the adapter) and it comes with all the wiring and circuit breakers you will need to wire in the brake controller. The only other parts you will need are a circuit tester like # PTW2992, and, if your brake controller doesn't have a wiring adapter, you will need # 20127 (for Tekonsha or...
  view full answer...


• Parts Needed to Add Trailer Brakes to 1998 Coleman Pop Up Trailer
• To add electric brakes to your 1998 Coleman pop up camper you should be able to use the Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA and then hub and drum assembly # AKHD-545-35-EZ-K for a 5 on 4-1/2". You just need to make sure that your current bearings are # L68149 and # L44649 plus verify that your grease seal has an inner diameter of 1.719". If you have something else please let me know and I can let you know what alternative parts you need. You also need to add a 7-Way...
  view full answer...


• Parts Needed to Add 7-Way Connector and Install Brake Controller on 2011 Chrysler Town and Country
• Thank you for you support of etrailer.com! Since you already have the Curt wiring harness installed on your 2011 Chrysler Town and Country, to set your vehicle up to control your trailer's electric brakes you will only need a trailer brake controller, like the Tekonsha Prodigy P3 # 90195 that you referenced, and the Universal Installation Kit for Trailer Brake Controller # ETBC7. The Installation Kit # ETBC7 includes a 7-Way and 4-Way vehicle-side trailer connector that will allow you...
  view full answer...